濟南變速箱維修人員提醒您，自動變速箱打滑主要是指離合器組合后發動機不能完全傳遞到主動輪上，使車輛難以啟動，發動機在行駛或加速時轉速過高，但速度較慢的現象。自動變速箱打滑通常伴隨離合器打滑。

Jinan gearbox maintenance personnel remind you that the slip of automatic gearbox mainly refers to the phenomenon that the engine cannot be completely transferred to the driving wheel after the clutch is combined, making it difficult for the vehicle to start, and the engine speed is too high but slow when driving or accelerating. Automatic transmission slip is usually accompanied by clutch slip.

當出現故障時，車主應盡快將車輛送往維修站進行維修。但許多車主混在一起，造成變速箱嚴重?fù)p壞。離合器打滑的根本原因是壓力片不能牢固地壓在從動盤摩擦片上，或者摩擦片的摩擦系數過低。

In case of failure, the owner shall send the vehicle to the maintenance station for maintenance as soon as possible. However, many car owners mixed together, causing serious damage to the gearbox. The root cause of the clutch slipping is that the pressure plate cannot firmly press on the driven plate friction plate, or the friction coefficient of the friction plate is too low.

如果發現摩擦片燒焦、硬化、油膩或過薄，則應視情況進行修復或更換，并檢查膜片彈簧的狀況，如彈簧的疲勞、開裂和失效等。

If the friction plate is burnt, hardened, greasy or too thin, repair or replace it as appropriate, and check the condition of the diaphragm spring, such as fatigue, cracking and failure of the spring.

離合器打滑也可能是由于壓力板或飛輪的變形和磨損，或離合器控制機構的調整不當，導致踏板的自由行程小。對于使用機械式電纜控制機構，電纜可能會卡住、自動調整故障等，也會導致故障。

Clutch slip may also be caused by deformation and wear of the pressure plate or flywheel, or improper adjustment of the clutch control mechanism, resulting in small free stroke of the pedal. For the mechanical cable control mechanism, the cable may be stuck, automatic adjustment failure, etc., which may also lead to failure.

除此之外，離合器主缸中的離合器液壓控制機構也會發生故障。對于自動變速箱的打滑故障，除了檢查離合器制動器等部件的打滑磨損外，還應注意油壓、油泵和閥體。

In addition, the clutch hydraulic control mechanism in the clutch master cylinder will also fail. For the slip failure of automatic transmission, in addition to checking the slip wear of clutch, brake and other components, pay attention to the oil pressure, oil pump and valve body.

自動變速箱打滑故障的發生怎么回事？以上就是問題的相關內容了，您對此有什么想咨詢的就來我們網站http://看看吧！

What happened to the slip fault of the automatic transmission? The above is the relevant content of the question. If you have any questions, please come to our website http:// Look!